The basic number cutters are ideal for house numbers, plaques, or address signs. Shown are 3" to 9" cutters in 1" steps. Use alone or with our plaque cutters (sold separately). The 6" and 9" cutters are mirror images, so order only one.
Number cutters are sold as sets in a separate listing. Cutters are reinforced to reduce distortion when used with pottery clay.
For small cutters, put cling film or a thin plastic sheet (or use cornstarch) between the cutter and clay for easy release. Avoid 1–3 inch cutters with pottery clay. Number cutters work best when clay is near leather-hard to prevent pulling and distortion.
Note: It’s best to avoid using 1–3 inch cutters for pottery clay, as they can be awkward to handle and may not give clean, consistent results.
Our made-to-order cutters are printed on a 3D printer using an olive-green, food-safe PLA plastic filament, ensuring durable, lightweight construction and safe contact with food.
Our cutters are fabricated with a 20mm sharp edge to produce a clean, precise cut. They are carefully engineered to create a distinct, framed shape that provides consistent sizing across pieces, helping to speed up the cutting process and improve overall workshop efficiency.
As our products are made to order, please allow up to 10 business days for processing your order. Unless otherwise specified, measurements refer to the widest dimension of the item. Please note that made-to-order products are non-refundable.
Please note: PLA cutters and textured rollers should be hand washed only in warm (not hot) soapy water, because exposure to high heat from dishwashers or very hot water can cause them to warp or melt. Gently scrub any creases or detailed areas with a soft toothbrush to remove residue. After washing, thoroughly air dry or hand dry them immediately to ensure no moisture remains. Store the tools in a cool, dry place out of direct sunlight to help prevent warping. Avoid using harsh or abrasive cleaning materials or scouring pads that could damage the surface.
For smaller size cutters it is recommended using cling wrap or other thin plastic sheet between the clay for easy release or cornstarch. The 1-3 inch cutters are not recommended for pottery clay. The number cutters work at their optimum when the clay is approaching leather hard to avoid pulling and distortion of the clay.
Our made-to-order cutters are printed on a 3D printer using an olive-green, food-safe PLA plastic filament, ensuring durable, lightweight construction and safe contact with food.
Our cutters are fabricated with a 20mm sharp edge to produce a clean, precise cut. They are carefully engineered to create a distinct, framed shape that provides consistent sizing across pieces, helping to speed up the cutting process and improve overall workshop efficiency.
As our products are made to order, please allow up to 10 business days for processing your order. Unless otherwise specified, measurements refer to the widest dimension of the item. Please note that made-to-order products are non-refundable.
Please note: PLA cutters and textured rollers should be hand washed only in warm (not hot) soapy water, because exposure to high heat from dishwashers or very hot water can cause them to warp or melt. Gently scrub any creases or detailed areas with a soft toothbrush to remove residue. After washing, thoroughly air dry or hand dry them immediately to ensure no moisture remains. Store the tools in a cool, dry place out of direct sunlight to help prevent warping. Avoid using harsh or abrasive cleaning materials or scouring pads that could damage the surface.
The basic number cutters are ideal for house numbers, plaques, or address signs. Shown are 3" to 9" cutters in 1" steps. Use alone or with our plaque cutters (sold separately). The 6" and 9" cutters are mirror images, so order only one.
Number cutters are sold as sets in a separate listing. Cutters are reinforced to reduce distortion when used with pottery clay.
For small cutters, put cling film or a thin plastic sheet (or use cornstarch) between the cutter and clay for easy release. Avoid 1–3 inch cutters with pottery clay. Number cutters work best when clay is near leather-hard to prevent pulling and distortion.
Note: It’s best to avoid using 1–3 inch cutters for pottery clay, as they can be awkward to handle and may not give clean, consistent results.
Our made-to-order cutters are printed on a 3D printer using an olive-green, food-safe PLA plastic filament, ensuring durable, lightweight construction and safe contact with food.
Our cutters are fabricated with a 20mm sharp edge to produce a clean, precise cut. They are carefully engineered to create a distinct, framed shape that provides consistent sizing across pieces, helping to speed up the cutting process and improve overall workshop efficiency.
As our products are made to order, please allow up to 10 business days for processing your order. Unless otherwise specified, measurements refer to the widest dimension of the item. Please note that made-to-order products are non-refundable.
Please note: PLA cutters and textured rollers should be hand washed only in warm (not hot) soapy water, because exposure to high heat from dishwashers or very hot water can cause them to warp or melt. Gently scrub any creases or detailed areas with a soft toothbrush to remove residue. After washing, thoroughly air dry or hand dry them immediately to ensure no moisture remains. Store the tools in a cool, dry place out of direct sunlight to help prevent warping. Avoid using harsh or abrasive cleaning materials or scouring pads that could damage the surface.
For smaller size cutters it is recommended using cling wrap or other thin plastic sheet between the clay for easy release or cornstarch. The 1-3 inch cutters are not recommended for pottery clay. The number cutters work at their optimum when the clay is approaching leather hard to avoid pulling and distortion of the clay.
Our made-to-order cutters are printed on a 3D printer using an olive-green, food-safe PLA plastic filament, ensuring durable, lightweight construction and safe contact with food.
Our cutters are fabricated with a 20mm sharp edge to produce a clean, precise cut. They are carefully engineered to create a distinct, framed shape that provides consistent sizing across pieces, helping to speed up the cutting process and improve overall workshop efficiency.
As our products are made to order, please allow up to 10 business days for processing your order. Unless otherwise specified, measurements refer to the widest dimension of the item. Please note that made-to-order products are non-refundable.
Please note: PLA cutters and textured rollers should be hand washed only in warm (not hot) soapy water, because exposure to high heat from dishwashers or very hot water can cause them to warp or melt. Gently scrub any creases or detailed areas with a soft toothbrush to remove residue. After washing, thoroughly air dry or hand dry them immediately to ensure no moisture remains. Store the tools in a cool, dry place out of direct sunlight to help prevent warping. Avoid using harsh or abrasive cleaning materials or scouring pads that could damage the surface.
